Start with what the box already settles
Shadowrun: Controlled Chaos is a five-miniature set, and the supplied listing says the figures come pre-assembled and unpainted. That changes the job: you are not clipping parts from a sprue or fitting arms and heads. Your assembly work is limited to checking the figures, deciding how they meet their bases, and preparing a clean surface for paint. Treat the pre-assembled state as the starting point, not a reason to skip inspection.
The set contains Khronostatic (Human Face), Happy (Ork Street Sam), L33roy (Dwarf Decker), Hell Hunt (Elf Mage), and Tailwind (Troll Adept Brawler). The listing also names Shadowrun Sixth World and the Shadowrun: Takedown board game as intended uses. Those five identities are useful when you plan basing: a decker, a mage, a face, a street sam, and a brawler each read differently on the table, and a base that supports one silhouette may crowd another.
What the catalog confirms before you glue anything
- Shadowrun: Controlled Chaos Miniatures: Shadowrun: Controlled Chaos expands your games of Shadowrun with five all-new minis. The pack is a five-model set, so plan your assembly and basing session around five figures rather than a single character.

Shadowrun: Controlled Chaos Miniatures - Shadowrun: Controlled Chaos Miniatures: Comes pre-assembled and unpainted. You can skip multi-part assembly and go straight to inspection, base fitting, and paint preparation.
- Shadowrun: Controlled Chaos Miniatures: Featuring Khronostatic (Human Face), Happy (Ork Street Sam), L33roy (Dwarf Decker), Hell Hunt (Elf Mage), and Tailwind (Troll Adept Brawler) Miniatures. Knowing each runner's role helps you choose bases and arrange the crew so the figures remain readable on the table.
- Shadowrun: Controlled Chaos Miniatures: This set of minis is great for use with Shadowrun Sixth World and the Shadowrun: Takedown board game. The listed compatibility points to roleplaying and board-game use, which is where base stability and clear silhouettes matter most.
A safe order for checking and basing the five runners
The supplied information does not include a manufacturer assembly sequence or base-size specification. The steps below are a practical workshop order built around the confirmed fact that the minis arrive pre-assembled and unpainted. They are not manufacturer instructions, and they do not replace any guidance that comes with the product.
- 1. Unpack and inspect all five figures: Check each runner for visible damage or loose parts before you commit glue or paint. Because the set is pre-assembled, you are confirming the figures are intact rather than building them.
- 2. Match each figure to its intended base: The listing does not state base sizes. Dry-fit each figure on the bases you plan to use and check that the feet or contact points sit within the base edge. Tailwind, the Troll Adept Brawler, is the figure most likely to need a wider footprint, but confirm this by dry-fitting rather than assuming a size.
- 3. Clean and key the contact points: Remove any dust or mould-release residue from the underside of the feet and the top of the base. A light score on both surfaces gives glue something to grip. The supplied information does not name a specific cleaning agent, so use a method you already trust for your miniature material.
- 4. Glue the figure to the base: Apply a small amount of glue to the contact point, press the figure into place, and hold it until the bond takes. Keep glue away from painted surfaces and from the detail on the figure's feet.
- 5. Add basing texture before painting: Apply texture around the feet, not over them. Work one figure at a time so you can keep the runner's silhouette clear and avoid burying ankles or weapons.
- 6. Let everything cure before priming: The supplied information does not give a drying or curing time. Follow the glue and texture product labels, and do not prime until the base work is fully set.
Choosing bases when the listing does not give a size
The product record does not supply a base diameter or a base-size specification, so there is no catalog number to copy. That absence is a decision limitation, not evidence that no suitable base exists. The practical approach is to dry-fit each runner and choose a base that supports the figure without overhanging the table footprint.
For a five-model set used in Shadowrun Sixth World or Takedown, consistency across the crew usually matters more than matching a particular measurement. Pick one base style for all five, then adjust only where a figure genuinely needs more room. Tailwind's brawler build is the obvious candidate for a larger base, while L33roy the Dwarf Decker may sit comfortably on a smaller one. Confirm both by test-fitting before you glue.
Basing choices by runner role
The listing identifies each figure by role, which is enough to plan a readable base without inventing rules. Use this as a starting point for dry-fitting, not as a fixed size chart.
- Khronostatic, Human Face: A face character often reads best on a clean, low-profile base that keeps the figure's posture visible. Avoid tall texture that hides the legs.
- Happy, Ork Street Sam: A street sam tends to carry visible gear. Keep the base texture low around the feet so weapons and stance stay legible.
- L33roy, Dwarf Decker: A shorter silhouette can disappear behind heavy basing. Use a flatter base and keep the texture below ankle height.
- Hell Hunt, Elf Mage: A mage's silhouette often includes a raised arm or staff. Check that the base does not make the figure top-heavy, and dry-fit before gluing.
- Tailwind, Troll Adept Brawler: The brawler is the figure most likely to need a wider base for stability. Test the footprint and choose a base that keeps the center of gravity over the middle.
Checkpoints before you prime
- Every figure sits flat: Rock each runner gently on the table. If it wobbles, the base or the glue joint needs attention before paint.
- No glue on visible detail: Check feet, ankles, and the underside of the base. Excess glue can obscure detail and interfere with primer.
- Texture stops below the ankles: Basing material should support the figure, not swallow it. Keep the runner's stance readable.
- All five are consistently based: A crew that shares a base style looks intentional on the table. Confirm the five figures read as a set before you move to painting.
What the supplied information leaves you to confirm
The listing confirms five pre-assembled, unpainted miniatures and names the runners, but it does not supply base sizes, a material specification, a recommended glue, or a curing time. It also does not include care, safety, or compatibility instructions beyond the named game uses. Check the packaging and any inserts that arrive with the set for those details, and follow the labels on your own glue, primer, and texture products.
That does not make the set hard to prepare. It means the assembly and basing decisions are yours to make by dry-fitting and inspection. Start with the five figures in front of you, choose bases that keep each runner stable and readable, and leave the paint until the glue and texture are fully set.


